Cart Overview

There are no items in your shopping cart

Sonifex RB-ML2

Stereo Microphone and Line Level Limiter
$0.00
1 option selected

(0 reviews)

When you need mic level controls, perfect for News and PC apllications. The RB-ML2 is a stereo microphone and line level limiter. The unit is mainly used where assistance with level control is required,

Product Options

RB-ML2 $406.00
RB-ML2 (115Volt Version) $406.00
  • The RB-ML2 is a stereo microphone and line level limiter. The unit is mainly used where assistance with level control is required, for protection of mixer inputs and to prevent distortion. Ideal for news-booths, and the input to PC workstations, it provides an economical level control solution.
    The RB-ML2 has two electronically balanced XLR-3 inputs, which are routed to a line amplifier, or microphone amplifier, via a rear push-button. The microphone amplifiers have independent pre-set gain controls, and DIP switches for a high pass filter (low frequency roll-off at 125kHz) and phantom power to provide +48V to the connected microphones.

    The outputs of these amplifiers are passed through a VCA limiter circuit that can operate jointly on the signals in stereo mode, or independently in dual mono mode. The rear panel mode switch changes the unit from dual mono to stereo. Stereo limiting operates by limiting both left and right outputs if either left or right input needs to be limited. Dual mono limiting operates by limiting left and right signals individually, so you can use the RB-ML2 as two separate mono mic/line limiters.

    The characteristics of the limiter can be set via level threshold pre-sets. For each channel there is an input gain and a threshold level control. With the limit threshold set to maximum, the input through to output can be normalised using the input potentiometers. Once the unit is acting as a buffer with gain/attenuation, the limit threshold level can be set, with the recovery adjusted for the application. The power LED indicates limiting by flashing.

    The two XLR-3 electronically balanced outputs can be set to either line or mic output levels via a push-button. This allows the RB-ML2 to be used in line with a line or mic input on a mixer, or similar equipment. 
     
    Please seklect the variant from the product options.

  • Audio Specification
    Maximum Input Level -6dBu (mic), +28dBu (line), electronically balanced
    Input Impedance >20kohms balanced bridging
    Input Gain Range Adjustable +22dB to +67dB gain (mic) via 2 x pre-set pots (L and R), 0dB gain (line)
    Maximum Output Level   -18dBu (mic), +28dBu (line), electronically balanced
    Output Impedance   <50ohms
    Output Gain Range   Adjustable -54dB to -24dB gain (mic), -8dB to +22dB gain (line), ref 0dBu line input, gain via 2 pre-set pots
    Limit Threshold   Adjustable -8dBu to +28dBu
    Frequency Response   20Hz - 20kHz +/-0.1dB (600ohm load, ref 1kHz)  
    Noise (RMS)   <-70dB unity gain, ref +8dBu output
    Distortion   <0.02% THD + N @ 1kHz, ref +8dBu output
    Headroom   27dB for 3mV input
    Common Mode Rejection (Line)   >66dB typically
    Common Mode Rejection (Mic)   >86dB typically
    Phantom Power   +48V
    LF Filter   125Hz @ 6dB/octave
    Connections and Controls
    Analogue Inputs   2 x XLR 3 pin female mic or line switchable (balanced)(L and R)
    Mic/Line Input Control   2 x push-buttons for mic/line input
    Analogue Outputs   2 x XLR 3 pin male mic or line switchable (balanced)(L and R)
    Mains Input   Filtered IEC, switchable 110-120V or 220-240V, fused, 6W max
    Mic/Line Output Control   2 x push-buttons for mic/line output
    Phanton Power and LF Filter   1 x 4 way dip-switch
    Mono/Stereo Mode Select   1 x push-button
    Limit Level Threshold Set   2 x preset pots
    Physical Specification
    Weight Nett: 1.1kg Gross: 1.5kg
    Dimensions Raw: 28cm (W) x 10.8cm (D) x 4.2cm (H) (1U) Boxed: 36cm (W) x 20.5cm (D) x 6cm (H)
  • Review this product


Other Products You Might Like

Featured manufacturers

Please Wait